Mark L MLC L10 Audio Looper

MLC L10 Audio Looper MLC Audio Looper L10 is equipped with 10 effect loops. L10 is controlled by MIDI CC (Control Change) and MIDI PC (Program change) commands over 16 MIDI channels. L10 is compatible with any type of MIDI controller capable of sending CC & PC commands, but to ensure proper operation and maximum effectiveness we recommend using MLC controllers. Transparent sound with the best professional grade Burr Brown OPA line driver for zero loss of tone or touch dynamics. Silent switching and full MIDI compatibility. Tour grade construction, simple to setup and control. perfectly transparent sound ultra-clean sound signal to noise ration comparable to CD quality recording s(102dB) no dynamic loss full bandwidth silent, click-free switching, even in high gain level MIDI compatibility, PC commands and CC commands high grade low noise line driver (BURR BROWN OPA Line Driver) alternating or direct current operation Handcrafted in Gdansk Poland MLC S-10 S is equipped with 10 effect loops, MLC S-10 S is controlled by MIDI CC (Control Change) and MIDI PC ( Program Change) commands over 16 MIDI channels. MLC S-10 S is compatible with any type of MIDI controller capable of sending CC and PC commands, but to ensure proper operation and maximum effectiveness we recommend using MARK L controllers. The effects loop can be hooked up with: 10 mono effects (10 effects plugged in before the amplifier) 10 mono effects (10 effects plugged in the amplifier’s FX LOOP ) By dividing the loop into two sections we can plug in: 10 mono effects (6 before the amplifier and 4 in the amplifier’s FX LOOP) FRONT PANEL: The front panel consists of 12 LED diodes informing which loop (L1-L10), MIDI light which informs if the device is receiving MIDI signals and STORE. To connect audio through a high grade line buffer, connect to the JACK 6,3MM GUITAR IN . REAR PANEL: The rear panel consists of 6,3 mm ‘jack’ receptacles used for connecting effects, audio signals and control the amplifier and other devices LINK OUT - direct OUT ( from front panel GUITAR IN) INPUT 1 - effects loop 1-6 IN ( without high impedance input buffer ) OUTPUT 1 - effects loop 1-6 OUT ( high impedance output buffer ) INPUT 7 - effect loop 7 IN SEND 7 - effect loop 7 SEND RETURN 7 - effects loop 7 RETURN OUTPUT 7 - effects loop 7 OUT INPUT 8 - effect loop 8 IN SEND 8 - effect loop 8 SEND RETURN 8 - effects loop 8 RETURN OUTPUT 8 - effects loop 8 OUT INPUT 9 - effect loop 9 IN SEND 9 - effect loop 9 SEND RETURN 9 - effects loop 9 RETURN OUTPUT 9 - effects loop 9 OUT INPUT 10 - effect loop 10 IN SEND 10 - effect loop 10 SEND RETURN 10 - effects loop 10 RETURN OUTPUT 10 - effects loop 10 OUT TUNER OUT - ISO separated TUNER out 10 xSend - used for connecting the effect’s INPUT 10 x Return - used for connecting the effect’s OUTPUT GND/LIFT - chasis ground lift switch MIDI IN - used for communications with a midi controller MIDI OUT THRU - midi thru outfor additional device MIDI CHANNEL - switch used for switching channel from 1 to 16 POWER IN - power supply socket for AC 9V/1A (AC Plug 2,5mmx5,5mm) EXT POWER IN - phantom power for midi controller (AC Plug 2,5mmx5,5mm) Technical Specification: Power in: Power supply socket for AC 9VAC/1A Plug 2,5 mm x 5,5 mm Operational temperature: -15˚C / +50˚C Height: 1U (44 mm) rack space Width: 19" (482 mm) rack space Lenght: 185 mm Weight: 1,5 kg / 3 pounds User Manual